请问广汽传祺gs4刹车异响怎么回事？传祺gs4踩刹

　　请问广汽传祺gs4刹车异响怎么回事？传祺gs4踩刹车异响「专家回答」

　　据和记百科网站「回不去的以往」消息，近日，请问广汽传祺gs4刹车异响怎么回事？传祺gs4踩刹车异响「专家回答」引发热议，传祺gs4踩刹车异响同样引起许多争议，对此众网友各抒己见。但到底是怎么回事呢？和记百科为您解答。

　　

广汽传祺gs4刹车异响怎么回事

 

　　1、新车磨合。

　　2、ABS系统的正常启动。

　　3、刹车片出现金属硬点，刹车片内部会有一些细小的金属颗粒，轻踩刹车就会发出尖锐刺耳的声音，这种问题可以猛踩几脚刹车或者把刹车片拆下来重新打磨，也可更换更好一点的刹车片。

　　4、刹车片磨损严重，开始报警。

　　5、刹车盘磨损严重。

　　6、刹车片的装配问题，试着把刹车片重新安装一下，往刹车片与刹车卡钳连接处涂抹黄油或者专用润滑油即可解决。也有可能是刹车片装反了，重新装配即可。

　　7、刹车分泵不回位，多是刹车导管的问题，刹车导管内生锈或者润滑油变脏都会导致回位不良，清理刹车导管，用细砂纸打磨并涂抹新的润滑油即可。也有可能是刹车分泵的问题，需要更换刹车分泵，但这种故障比较少。

　　8、刹车导管或卡钳的配合问题。刹车导管除了因为变脏卡滞之外，也有可能是刹车导管与刹车卡钳的配合间隙过大，二者之间有旷量导致产生的异响，更换新的刹车导管或者刹车卡钳（通常都是换刹车卡钳，因为刹车卡钳的孔径可能会因磨损变大，而刹车导管磨损相对较小），或者往刹车导管上缠一层防水胶带以减小配合间隙。

　　9、考虑到刹车大部分时间都是工作在车辆前进之中，所以刹车片长时间的朝一个方向磨损就会相应的在倒车面造成一些毛刺，当车辆在倒车时，当车辆在倒车时踩刹车，毛刺与刹车盘摩擦产生异响，当遇到这种情况时可以先不解决，或者有时间前往4S店或者维修厂拆下来打磨一下，也可以更换更好的刹车片。

　　10、倒车踩刹车会听到咯噔的声音。这是刹车卡钳因为摩擦向上运动，撞击到上部托架产生的异响。属正常现象，若异响较大，可能就需要进行维修了。

　　

传祺gs4踩刹车异响

 

　　1、新车磨合：刹车片的磨合是一个很重要的环节，通常跑几百公里后，才能感觉刹车比较舒服，不再会有异响。

　　2、刹车盘里有沙子：车辆行驶当中，也许会有很细小的沙粒进到片和盘的中间，发生摩擦从而出现异响，这种情况一般不需要维修，跑一跑使小沙粒掉出来即可。

　　3、刹车盘的固定螺丝丢失或损坏：这种情况也会引起刹车异响。

　　4、刹车系统出现故障：此时需要检查和维修。

　　

　　【英文介绍/For English】：

　　

　　1. New car run-in.

　　2. The normal start of the ABS system.

　　3. There are metal hard spots on the brake pads. There will be some small metal particles inside the brake pads. When you step on the brakes lightly, there will be a sharp and harsh sound. For this problem, you can slam on the brakes a few times or remove the brake pads and re-polish them. Better brake pads can be replaced.

　　4. The brake pads are seriously worn, and the alarm is started.

　　5. The brake disc is seriously worn.

　　6. For the assembly of the brake pads, try to reinstall the brake pads, and apply butter or special lubricant to the connection between the brake pads and the brake calipers. It is also possible that the brake pads are installed backwards and can be reassembled.

　　7. If the brake cylinder does not return, it is mostly the problem of the brake catheter. Rust in the brake catheter or dirty lubricating oil will lead to poor return. Clean the brake catheter, polish it with fine sandpaper and apply new lubricating oil. There may also be a problem with the brake cylinder, which needs to be replaced, but this failure is relatively rare.

　　8. The fit of the brake conduit or caliper. In addition to the fact that the brake catheter is dirty and stuck, it may also be that the gap between the brake catheter and the brake caliper is too large, and there is an abnormal sound caused by the gap between the two. Replace the brake catheter or brake caliper (usually with a new one). Change the brake calipers, as the hole diameter of the brake caliper may become larger due to wear, and the brake duct wear is relatively small), or wrap a layer of waterproof tape on the brake duct to reduce the fit gap.

　　9. Considering that the brakes work most of the time when the vehicle is moving forward, the wear of the brake pads in one direction for a long time will correspondingly cause some burrs on the reversing surface. When the vehicle is reversing, when the vehicle is reversing, press Brakes, burrs and brake disc friction produce abnormal noise. When you encounter this situation, you can leave it unsolved first, or you can go to the 4S shop or repair shop to remove it and polish it, or you can replace the better brake pads.

　　10. When you step on the brake in reverse, you will hear a "click" sound. This is the abnormal sound produced by the brake caliper moving upward due to friction and hitting the upper bracket. It is a normal phenomenon, if the abnormal noise is large, it may need to be repaired.